Sunday, December 16, 2012

Cut springs and other things

So I spent most of Saturday on another project; helping clad my daughters Christmas present; a "Cubby House" - the reason it's in quotation marks is that it's rather well built - silverwrapped, will have pink bats, and it's on a movable steel skid that is designed to fit into our trailer when we move (we're currently renting). It's a bit of forward planning so as she gets older, instead of falling into dis-use, it will become her own "space" for study etc.




Next up, a photo from work I did a week ago but forgot to take and upload - the mounting bracket and location for the Ford EEC-IV ECU:


Next, here's what I decided to do this weekend. I have problems staying motivated on one task at a time (if you've been reading this build the whole way, that may have become somewhat obvious to you in the way I chop and change between different aspects of the build!). I decided to cut the springs for more low. The shocks on the car seem really good (no extra bounce etc) but when I drove it last (i.e. when it was still registered, but with overheating issues from the engine limiting drive-time) it had far too much body roll for my liking.


Before


Much to the chagrin of the E21 evangelists on Bimmerforums (see discussion thread here), I decided to cut the springs as an initial step. I don't intend on returning it to standard height with factory springs (if I need it higher for Rally down the track, I will do it with coilovers with stiffer springs to control the body roll!) so am not losing anything by cutting the originals. Plans down the track (for adjustability and added stiffness) is to get a second hand set of S13 or R33 coilovers to make fit and work on this car. In the meantime, the fronts are Bilstein and the rears Koni Yellows, so the shocks should still do okay for a while.



I haven't taken an after version of this shot yet as I'm waiting for the springs to full settle overnight; however this is a "Before" shot of the driver's side rear standard height.



I went with a two coil cut, as recommended by one of the few people on BF not abhorred by the sacrilege I was about to bestow on this poor 3 series (let's remember, I tried selling this car intact before I began this project but got zero interest - if it wasn't for this project it would have been scrap metal a long time ago!).



I used an air powered grinder at first. Unfortunately, this one is cheap and fairly hungry for air. My grandfather bought it at Aldi then decided he didn't really need it. I'm glad, as it's the only "straight" grinder I have, and despite having to stop many times and wait for the air compressor to "re-charge" so I could do the job, it was a much better tool for the task than my normally trusty angle grinder due to doing the cutting in the car. Here's a bit of info for anyone looking at lowering an E21 this way: with the rear of the car off the ground, the rear springs aren't really under any compression. There's enough to stay captive, but not enough to break your grinder/arms/face when you cut through. If you're unsure, try and compress the springs slightly with your hand - if you can get a bit of wiggle out of them then it's probably OK.



Enlisting the ever present help of Mr Hamilton, yet again. Cutting the spring becomes a two step process, as we're taking off two coils, it's not possible to remove the cut off section easily without cutting it in half again; it's easier to cut two, then in half than to cut one at a time, as the first is very close to the spring perch (and you don't want to be cutting that!) - see below:



Here it is with both rears done, and lowered back down - note it hasn't fully settled yet. I'm not expecting any massive changes as the springs have already put in years of work, however the change in the amount of spring/leverage to the weight of the vehicle may mean they have some slight give in a day or two - we'll see what happens!



In the front, you MUST cut full coils, as the top hat and bottom spring perch have formed shapes for the spring to seat into. In the rear, you can get away with cutting however much you need as you can just rotate the bottom rubber.



Here's another tip for those of you contemplating cutting your springs in-car like we did. Front springs ARE under compression with the weight of the car off them! Here's what happens if you try cutting them in car, without spring compressors:



Instead, you need to undo the top nut (remove the cap with a pair of multigrips, undo the 19mm nut with a socket or offset spanner - a deep impact socket would be best however if the whole shaft rotates you might need to use an offset spanner and a smaller spanner to hold the flat sections at the top of the shock shaft to stop it rotating. Take care not to destroy your elbow on the LHS when the nut finally breaks - from experience, the bonnet catch hook is in just the right position to cause a great deal of pain!



Undoing both sides at once will give you the advantage of having more room to play with, and the disadvantage of the suspension having much more chance of being in the wrong place when you want to try and get it to go back where it should! We had both undone for the first side, and as a result re-fitting this side took a great deal longer than it should have!



The biggest issue we found was with getting the assembly back into the car - the top spring hat kept getting caught on either the top of the thread for the shock, or the collar just beneath the thread. If I had DECENT spring comressors that weren't: A) too long, or B) just plain trying to kill us, this would have been a much easier step as we could have placed the top hat where we needed it. Instead, on both sides, I had to file a slight taper into the hole on the hat to make it easier to guide into place.


There was still some difficulty getting the shock into place, we managed to get it centered but it was still binding slightly inside the top bearing. A small spray of WD40 and gentle redirection with a flat head screwdriver (you could see which way it was out, and gently push in the other direction) then allowed it to pop into place enough that the nut could be done up further pulling it through. The nut was then removed and re-installed with the correct original washers (one flat and one spring washer).



A lot of people mentioned on BF about the front lower control arm hitting the frame rail when the car is too low. Here's how mine sits now. With Michael jumping on this corner of the car, the rail does not bottom out, in fact it only seems to go about as far above horizontal as it is below when un-loaded as per this image. We will see how it goes in practice! As this is not a street car, if it DOES hit, I am quite happy to cut any fouling areas around the mouth of the subframe, or indeed to make a custom lower control arm to replace the standard one, allowing more clearance. If I were to make a custom arm, I would possibly replace the front swaybar with a simple adjustable rose-jointed locator bar.



Here's how it sits now; it's a significant improvement if I do say so myself, and the shocks don't appear to be in danger of bottoming out with two coils removed all round. The front still looks a tiny bit too high, however I don't really want to remove another full coil. Perhaps I could lower the spring perch? On the subject of modification, if the rear geometry is too messed up with the lowering that has been done, it looks like a relatively easy job to lift the entire rear subframe by at least an inch with only some minor modifications for clearance of the upper control arms and the tailshaft, and raising the diff mount to suit. I guess we'll see what happens there; perhaps down the track when it's coilover time, the subframe will get some fettling too!

Friday, December 14, 2012

Isolator switch bracket

Spent just over an hour last night making up the mount for the battery isolation switch last night from an offcut of aluminium chequerplate. The photo below doesn't show but the far side has about 3" going downwards; it's only sitting in the trans hole for the photo and will be mounted in about the same spot but on the interior side of the trans tunnel in approximately the location pictured.



The good news is, it looks like a factory Falcon starter motor wire will reach from this location to the starter motor without any further modification.

The reason I say "further" modification, is that I had to enlarge the holes to clear the stud for the isolation switch. Anyone planning on doing this, don't forget to make sure you have connectors that will fit on your existing cables, or buy some that will. Drilling/filing ring terminals is not particularly fun stuff!

Thursday, December 13, 2012

Battery "Isolation" Wiring


Went to mount my isolation switch last night and ran into a few queries that I couldn't find any quick or easy answers to; relating to where the switch is accessible from.

ANDRA (drag racing) says if the car runs quicker than 12s (1/4 mile) or 7.7s (1/8th mile) then it needs an externally accessible kill switch.

My original plan was to fit the switch in the cabin, within reach of the driver (and for Rally, within reach of the co-driver also) - the obvious location for this is the trans tunnel as with the battery located per pictures in previous posts (middle of back seat area) this is right in-line with where the battery wiring needs to run.

Rally Australia documents via CAMS state that while most Rally cars already run isolation switches, there is not actually a standard or a requirement relating to these; so that's safe for now, however one would assume that once standardised (or IF) that these switches will also need to be accessible by a marshal should the driver be incapacitated due to an accident.

I haven't yet been able to find info in CAMS but some posts on forums indicate that V8SC and other racing require this to be fitted to the base of the A-pillar. Given my seating position, this isn't a great idea as I can't REACH the A pillar with the seat mounted low and central as intended.

I've discovered what I think is the solution to all of these problems, firstly wiring the switch as follows from a Diagram posted on Skylines Australia (http://www.skylinesaustralia.com/forums/topic/324683-wiring-up-a-cams-approved-batt-isolator/):

A concern (and the reason for putting the alternator charge wire to the "always on" side of the switch) is that when you don't have a battery in place, load changes on the alternator by switching off high current devices such as lights/ignition etc can damage the alternator; in a normal car this extra momentary current increase from the alternator is absorbed by the battery, which acts as a huge capacitor. In the diagram above, the solution is that engine gets cut due to ignition and fuel pump being cut, and the battery is still there to take the current increase from that; while the engine/alternator spin down. The 100A fuse is there in case the cause for concern is a shorted alternator charge wire; this will cut that wire in that instance preventing further dramas. I will also have a single 5 or 10A wire running from the battery side of the switch to the KAM +ve on the ECU; this will ensure the ECU doesn't reset it's learning/adaption every time the car is switched off with the isolation switch.

I am still going to locate the switch on the transmission tunnel but have found a solution to the "externally accessible" part of the equation:

http://atspeedracing.co.uk/products/index.php?main_page=product_info&cPath=96&products_id=326&zenid=7c989739515573a56780d5a3188c5087
I will put this on a bracket at the switch (the switch has a provision for a lanyard/pull cable) and then run it to the fuel filler door, which will identify the presence of the switch with the standard blue triangle for ease of identification by marshals in case of a crisis.

Tuesday, December 11, 2012

Battery switch

I got my battery switch today, it is rated for 120A continuous or 500A for short periods (i.e. cranking). For only $18 they're a no brainer. Available from all Jaycar stockists.

Monday, December 10, 2012

No updates today

Hi all,

had a different project I spent some time on over the weekend, so didn't get any more work done on the E21. Plan to finish at least the driver's seat mount some time in the next few days though; and have cleared the pit side of the shed so I can get underneath to remove the engine/gearbox. This will mean I can finish welding the firewall and will be able to look at getting the good motor out of the Falcon and installed.

-C

Tuesday, December 4, 2012

Seat mounts

So the ECU wiring is in, and should hopefully work. I won't know for certain if it functions correctly until I actually get a motor (with manifolds etc intact) in to the car. The existing unit in the car is partially disassembled and was only fitted for sizing and mount building purposes.


In yet another tangent from the task immediately at hand, we started to work on a few other parts of the car needing attention. Firstly we are making seat mounts. I initially removed the existing rails from the seat and sat it directly on the floor, as far back as it could go (against the rear seat shelf) - this allowed about 10cm clearance between the top of my helmet and the lower-most part of the sunroof assembly, but did not allow me to see the bonnet. I could drive like this but it may prove difficult to see the track. I tried with around 30cm of books on top of the seat and this still allowed a decent amount of headroom but I could then see the front edge of the bonnet and the ground about 5m in front of the car, perfect.


I am going to use two bars as pictured above for the seat mounts; one can be RHS but because of the shape of the floor, the front mount needs to be angle iron welded in. I will then fit some angle iron to the seats themselves so that it sits on top of these bars - the angle will be bolted to the seats, and then the seats and this angle will sit in place and be bolted at each side of the seat, to allow the seat to be easily removed. I was initially going to bolt from under the floor but if that leaves exposed bolt heads there's a risk of them grinding or being snapped off if the car bottoms out. I still may use these rails as the mounts and cut an access hole in the underside of the floor to access the bolt heads, this should protect them enough to be OK to use this way.


While I started making the seat mounts, Fletcher came around and cut up an old table for some scrap RHS, which Michael H proceeded to turn into the battery box you see above. To help isolate the battery and the fuel, the battery will be run inside the car. I still have to look into sealing and ventilating it to somewhere outside the cabin - I believe I should be able to vent it to one of the C pillars as they have ventilation ducts there standard.



As it sits at the moment, I don't have any angle to make up the front "bar" mount, and I have to finish welding in the RHS bar as well. Once the driver's seat is mounted, we will be able to begin sorting out pedals (we need to use a falcon pedalbox, as the clutch is cable operated, also the BMW accelerator assembly was attached to part of the rusted floor that has since been removed. The brake pedal from the falcon should just require a hole drilled to accept the push rod from the BMW assembly to function.

Sunday, December 2, 2012

Odd jobs

Got a bit bored with wiring so have done a little bit of a few other tasks.

Partially re-made the front radiator support area (pictures when it's done) so the light surrounds can be mounted properly.

Also made some headway into cutting out the boot floor to allow a falcon fuel tank to fit, I am going to avoid using a fuel cell unless completely necessary in the aim of keeping this as low-budget as possible.

I also gave the car a quick wash and machine polish; it came up pretty well considering it hasn't had more than a single pressure wash in the last two years or more.





There are some other things I'd like to do too (like cutting the springs) but I'm missing a few assorted bits and pieces to make them happen (i.e. cutting wheels for the grinder) - I'll have to grab those sorts of things over the next few weeks so I can cross some more of these tasks off the list.

Tuesday, November 27, 2012

Wires, wires and more wires!

Just spent three hours untaping a whole Falcon worth of looms. We won't need anywhere near the whole lot, so this will make the process of removing the unneeded wires much easier.

These photos show a LOT of wires, but it doesn't even come close to conveying just how many are here... just wow.



Progress Update

So, I have made some decent progress on the wiring today. Got the parker and low beam switch worked out, wired up and tested working all ok. Got the reverse light wired to the falcon gearbox and tested working all ok. Got the brake light switch wired up and working with the BMW pedalbox.

Took a quick snap of my daughter Scarlett putting the wiring through its paces - she loves playing with buttons and switches etc :)


Next job was to get the control panel wired before I start doing the motor loom. I've had the panel in the car for some time (I believe there are more photos down below of this), but nothing had been connected. It's now wired and back in the car, so I can start setting up relays etc for the various functions I have placed on this board.

Sunday, November 25, 2012

Wiring

Finally made a start to the wiring on the car over the last few days.

Since I started, I eventually tracked down a PDF wiring manual http://www.jtresto.com/e21/ETM_1979.pdf, but initially I went through with a battery charger and connected individual pins to determine which wires for the rear lights were which. I was a bit hasty removing the original wiring from the car so this was cut off at the base of the back seat. Once I'd determined which wires were for what, I extended them (with the original loom, which I still have, as I figured I'd need the connectors - thank god I did that - more on that later!). I am going to run the relays for everything in the car at the passenger footwell. I'll be putting a bar to stop passengers from being able to kick anything loose. The Battery will be in the boot and the master switch will be in the centre console near the hand brake and shift lever so either the driver or passenger can turn it off.

I dug out the engine bay loom and untaped it, then seperated out everything except the two headlight and indicator loom wires, shortened the ground wires and put terminals on them, and then extended this wiring and ran it also into the footwell.

I joined the front and rear indicators, and parker wiring together, and tested that I had all the things I wanted (I don't think I need a horn, I don't have a horn switch anyway) --> Headlights, Parkers, Indicators, High Beam, Reverse Lamps. I also ran the wire to the footwell for the rear demister. I don't know if I'll need it but it's easier to run the wiring now than to leave it until later and have to find/run it.

Then (and this is where keeping the connectors comes in) I tried to work out how the combination switch (High/Low and Left/Right indicators) works - turns out there is a (very proprietary) 12 pin plug (approx) and inside this plug these switches have both their pins wired; so you need to find BOTH matching pins to be able to use the switch. It's probably not a massive surprise for those of you who have done this sort of thing before, but it sure makes using a multimeter to work out which wires are used very time consuming - in the end I gave up and tracked down the wiring diagram mentioned above.

I've also cut back the loom for the hazard switch, and will be connecting that as well; it will get it's power (fused) from in front of the master switch, so the hazards can still be run in any incident where the rest of the power has to be cut off. The fuse should protect it from any other dramas though.

I taped an E-series flasher unit to a couple of relays, and have wired up the relays for the indicators/hazards, now I have to wire the indicator light into the hazard switch and connect it and the combo switch up for a test run. Once that's done, lights are practically done (N.B. I still have to work out the dash lamp wiring, but I'll treat that as a different job I think!)

Thursday, November 8, 2012

No news, so I'll post some photos instead!

Bonnet and front back on; almost forgot what it looked like!

Worked out that my sunroof actually opens! All along, I'd only thought it was a tilt roof as it just clicked like a ratchet when trying to turn the handle the other way (although it went too far past closed and seemed odd that there were rails for it to open right up). Managed to give it a bit of manual persuasion (pusing down and back on the top of the roof while winding the handle) and it opened. Once it got past the initial difficulty, it opened very easily and freely. It's still a bit stiff at the extreme point of closing or opening but I think that's just the interior trim catching on the frame, so I'll have a go removing that and then see if it's any better. Since the car will have limited ventilation when it's done, being able to open the sunroof will be a massive benefit for airflow through the car.

Had a stuck front wheel bearing or brake rotor corroded, to the point my normal method of moving the car (ride-on lawn mower) wouldn't move it, and you couldn't turn the wheel by hand. Hooked up one of the other cars in the yard (Ford Fairmont, also powered by a 4L I6) and it started moving no worries. Seems to roll fairly freely now so I'm going to assume it was just corrosion on the brake rotor from a bit of water.

Finally, here's a quick video of my (now retired) EB with the motor that currently seems destined to end up in the E21:

Sunday, September 9, 2012

Radiator

So, I got a bit carried away making room for the radiator. I am using a standard Falcon Radiator because it's perfectly suited to the motor, and because it's the same width as the engine bay :)
As you can see, it fits!
Still some fine tuning to do here to ensure the hose won't get rubbed through by metal, should only be minor work required though.
Will have to make some covers for this light - I prefer the twin-light look, so it'll be a bit like the Jagermeister Group 5 car :)
Routing this hose to the reservoir could prove to be interesting, the headlight bracket is going to be a bit of work!

Monday, August 27, 2012

Slow progress is better than no progress

I was out of action for most of the weekend but managed to get a couple of small things done in the spirit of keep going forwards:

I started going through my box of parts, and have fitted a harmonic balancer, power steering bracket and distributor to the engine.

Unfortunately the block I'm using has a snapped water pump bolt in one of the four holes. I know when it was used in one of our cars some time back, this never caused any leakage issues, so I'm going to pack the bolt hole with form-in-place-gasket when I fit the water pump to the motor and see how it pans out.

I'm not sure that I've got a tensioner in decent nick to use. I have a tensioner but it looks like one of the pulleys is stuffed. We'll see how it goes I guess.

Sunday, August 12, 2012

Trans tunnel done

Finally got around to doing the trans tunnel. It's been so long since the car had a full floor that it's surreal looking at it now!

I still have to weld the seam at the top but I'll do that from the engine bay with the motor out.